Interfacial bonding mechanism and bonding strength of AlTiCrN coating by cathodic arc ion plating

AlTiCrN coating was prepared on the surface of YT14 tungsten carbide cutting tools by cathodic arc ion plating with Ti, Al and Cr as targets. The surface morphologies, interface energy spectrum, phase and elements' binding energy of the coatings were observed with SEM, EDS, XRD and XPS, respectively, and bonding strength of the coating interface was measured with scratch tester. The results show that the phases of AlTiCrN coating are mainly composed of AlN, CrN and TiN, the crystal plane of (111) has a strong preferred orientation. The concentrations of Al, Ti, Cr, N in the coating are higher than those in the substrate, showing the gradient diffusion distribution at the bonding interface, while C atoms of the substrate have diffused into the lattices of TiN, AlN and CrN to form an obvious interdiffusion layer, and the average bonding strength of coating interface is 57.65 N. Copyright © 2014 John Wiley & Sons, Ltd.     

Transformation of hydrophobic surface into superhydrophobic surface by interfacial flower like silver films

Fabrication of superhydrophobic surface was achieved by electroless deposition of silver film and subsequent immersion into a mixture of stearic acid and cysteamine. The resultant superhydrophobic surface with flower and fall‐leaves like structure showed lotus leaf effect with the water contact angle of about 154° making copper surface water repellant. Copyright © 2014 John Wiley & Sons, Ltd.     

二环己基-18冠-6加速锶离子在微米管支撑的水/1,2-二氯乙烷界面上的转移反应

采用玻璃微米管支撑的液/液界面通过循环伏安法(CV)研究了二环己基-18冠6(DCH18C6)加速Sr2+在水/1,2-二氯乙烷(W/DCE)界面上的转移反应,考察了DCH18C6加速Sr2+在W/DCE界面转移的影响因素,如DCH18C6和Sr2+浓度等,并求算其络合物的稳定常数。实验结果表明,Sr2+与DCH18C6发生的是一个1:1的扩散控制的界面络合转移过程,其络合常数β为5.31×1023。本研究可为理解溶剂萃取Sr2+行为提供基础理论数据。     

Design of TiO2@graphene nanosheets with rough surface and its reinforcement to polyarylene ether nitriles

The interfacial interaction is extremely important when dealing with filler‐reinforced polymer materials. Herein, in order to improve the interfacial interaction with the polyarylene ether nitriles (PEN) matrix, a three‐dimensional rough structure was designed. First, needle‐like TiO₂ nanocrystals were grown on each surface of the graphene. Morphology analysis proved that rough TiO₂ nanocrystals were coated on the graphene nanosheets. Then, TiO₂@graphene/PEN composites were fabricated to investigate the filler–matrix interaction. Thereafter, the different polymer chains could be interlocked by the TiO₂ “needles” when the rough TiO₂@graphene was embedded into the polymer resin. The surrounding PEN polymer chains (work as ropes) could tie to the “needles” (work as wood pile). That is to say, the effective polymer chain length was greatly lengthened, resulting in the improvement of interfacial interactions and mechanical properties. Most importantly, the morphology, mechanical and rheological tests of the composites also proved the improvement of interfacial interactions and mechanical properties. Copyright © 2015 John Wiley & Sons, Ltd.     

Interface Engineering of a CoOx/Ta3N5 Photocatalyst for Unprecedented Water Oxidation Performance under Visible‐Light‐Irradiation

Cocatalysts have been extensively used to promote water oxidation efficiency in solar‐to‐chemical energy conversion, but the influence of interface compatibility between semiconductor and cocatalyst has been rarely addressed. Here we demonstrate a feasible strategy of interface wettability modification to enhance water oxidation efficiency of the state‐of‐the‐art CoO_x/Ta₃N₅ system. When the hydrophobic feature of a Ta₃N₅ semiconductor was modulated to a hydrophilic one by in situ or ex situ surface coating with a magnesia nanolayer (2–5 nm), the interfacial contact between the hydrophilic CoO_x cocatalyst and the modified hydrophilic Ta₃N₅ semiconductor was greatly improved. Consequently, the visible‐light‐driven photocatalytic oxygen evolution rate of the resulting CoO_x/MgO(in)–Ta₃N₅ photocatalyst is ca. 23 times that of the pristine Ta₃N₅ sample, with a new record (11.3 %) of apparent quantum efficiency (AQE) under 500–600 nm illumination.     

Correlation of size and oxygen bonding at the interface of Si nanocrystal in Si–SiO2 nanocomposite: A Raman mapping study

Raman spectroscopy/mapping is used to investigate the variation of Si phonon wavenumbers, i.e., lower wavenumber (LW ~ 495–510 cm⁻¹) and higher wavenumber (HW ~ 515–519 cm⁻¹) phonons, observed in Si–SiO₂ multilayer nanocomposite (NCp) grown using pulsed laser deposition. Sensitivity of Raman spectroscopy as a local probe to surface/interface is effectively used to show that LW and HW phonons originate at surface (Si–SiO₂ interface) and core of Si nanocrystals, respectively. The consistent picture of this understanding is developed using Raman spectroscopy monitored laser heating/annealing and cooling experiment at the site of the desired wavenumber, chosen with the help of Raman mapping. Raman spectra calculations for Si₄₁ cluster with oxygen and hydrogen termination show strong mode at 512 cm⁻¹ for oxygen terminated cluster corresponding to the vibration of surface Si atoms. This supports our attribution of LW phonons to be originating at the Si–SiO₂ surface/interface. These results along with XPS show that nature of interface (oxygen bonding) in turn depends on the size of nanocrystals and LW phonons originate at the surface of smaller Si nanocrystals. The understanding developed can conclude the ongoing debate on large variation in Si phonon wavenumbers of Si–SiO₂ NCps in the literature. Copyright © 2015 John Wiley & Sons, Ltd.     

正交复合材料面层夹层板非线性理论及应用

针对复合材料面层夹层板的构造和变形特点，考虑横向剪应力在面层和芯层粘结处的连续条件，应用Ｈａｍｉｌｔｏｎ原理建立了基于五个未知函数的正交铺设复合材料面层夹层板的非线性精化理论。对静力学问题，控制方程化简为由四个基本未知函数表述。文中还分析了简支正交铺设复合材料面层夹层板的非线性弯曲，给出了载荷—挠度特征关系和板中应力的分布状况。数值计算表明，夹层板面层和芯层粘结处的层间剪应力在工程设计中是十分重要的。     

SH波绕界面孔的散射

用波函数展开方法研究了SH波绕界面孔的散射问题。由入射、反射和透射波组成的自由波场与孔的散射场叠加成总波场。按照一定方式将两个半平面散射波场延拓于全平面，通过Hankel-Fourier展开方法求得了任意形状孔散射场的级数解。以椭圆形孔为例计算了孔边缘的动应力集中系数。     

THE INTERACTION PROBLEM BETWEEN THE ELASTIC LINE INCLUSIONS

ＩｎｔｒｏｄｕｃｔｉｏｎＯｆａｌｌｔｈｅｆｉｂｅｒ＿ｒｅｉｎｆｏｒｃｅｄｃｏｍｐｏｓｉｔｅｍａｔｅｒｉａｌｓ,ｔｈｅｓｈｏｒｔ＿ｆｉｂｅｒｃｏｍｐｏｓｉｔｅｍａｔｅｒｉａｌｎｏｔｏｎｌｙｓｔｒｅｎｇｔｈｅｎｓｔｈｅｍａｔｒｉｘｂｕｔａｖｏｉｄｓｄｅｆｅｃｔｉｏｎｓｏｆｔｈｅｌｏｎｇ＿ｆｉｂｅｒｃｏｍｐｏｓｉｔｅｍａｔｅｒｉａｌａｓｗｅｌｌ.Ｔｈｅｍｉｃｒｏ＿ｍｅｃｈａｎｉｃｓａｂｏｕｔｉｔｓｕｃｈａｓｆｒａｃｔｕｒｅ ,ｆａｔｉｇｕｅａｎｄｄａｍａｇｅｉｓｖｅｒｙｃｏｍｐｌｅｘ .Ｉｎｔｈｅｐｒｅｖｉ…     

On the interaction between a dislocation and a circular inhomogeneity with imperfect interface in antiplane shear

The solution of appropriate elasticity problems involving the interaction between inclusions and dislocations plays a fundamental role in many practical and theoretical applications, namely, it increases the understanding of material defects thereby providing valuable insight into the mechanical behavior of composite materials.Although the problem of a three-phase circular inclusion interacting with a dislocation in antiplane shear has been presented [Xiao and Chen, Mech. Mater. 32 (2000) 485], the analysis is limited to the classical perfect bonding condition. The current paper considers the solution for a homogeneous circular inclusion interacting with a dislocation under thermal loadings in antiplane shear. The bonding along the inhomogeneity–matrix interface is considered to be imperfect with the assumption that the interface imperfections are constant. It is found that when the inhomogeneity is soft, regardless of the level of interface imperfection, the inhomogeneity will always attract the dislocation. As a result, no equilibrium positions are available. Alternatively, when the inhomogeneity is hard, an unstable equilibrium position is found which depends on the imperfect interface condition and the shear moduli ratio μ₂/μ₁.